Skip to Content

AC/DC sources / sinks

AE Techron 7796 HC
High-precision, DC-capable linear power amplifier with a current capacity of up to 200 amperes
  • Extremely high continuous current & inrush power
  • Wideband DC-to-audio amplifier: DC – 250 kHz
  • Four-quadrant linear design with CV/CC operating modes
Yokogawa LS3300
Reliable calibration of power metres, current clamps and current sensors
  • Precise AC/DC power calibration for power meters, current clamps and current sensors
  • Designed for high calibration accuracy and long-term stability
  • for automated test equipment (ATE) and structured calibration procedures in test benches
Yokogawa GS200
DC voltage/current source
  • Output ranges: DC voltage up to ±32 V and DC current up to ±200 mA with 5½-digit resolution
  • USB, Ethernet, GPIB
  • 0.016% basic accuracy (voltage), 100 nV / 10 nA resolution
Yokogawa 2560A
A simple, accurate and cost-effective solution for the calibration of DC measuring instruments
  • DC voltage up to ±1224 V, DC current up to 36.72 A (up to 73.44 A with two units operating in parallel)
  • ±50 ppm (DC voltage), ±70 ppm (DC current); stability ±10 ppm/h (V), ±20 ppm/h (A)
  • DC V/I, thermocouples (TC) and RTDs, sweep function, output divider for linearisation and deviation tests, clear 7-segment LED display
Yokogawa 2558A
Cost-effective precision calibrator
  • Output ranges: DC voltage up to 30 V, DC current up to 200 mA
  • ppm range with very high long-term stability and low drift for reference calibrations
  • DC power supply for voltage and current, remote control via standard interfaces, suitable for automated calibration systems
APM SP-1U/2U
High-precision AC power source with switchable single-channel output
  • Power & output range: up to 4 kW per unit, up to 800 V and up to 200 A
  • Features: LIST/SEQUENCE, timer, OVP/OCP/OPP/OTP/SCP, remote sense, low ripple & high resolution
  • USB, LAN, RS232, RS485 as standard; GPIB optional; parallel/serial operation with up to 10 devices
AE Techron 7224
900VA, single-phase, 2U, industrial amplifier/battery simulator
  • High-performance 4-quadrant amplifier (up to 50 A / 158 V)
  • Wide-band DC–1 MHz signal generator
  • Flexibly configurable – voltage or current mode
Yokogawa GS820
Multi-channel source-measure unit
  • Multichannel Source-Measure Unit
  • Four-quadrant operation
  • Measurement resolution down to 1 pA
Yokogawa GS610
Programmable voltage/current source
  • Combines a voltage and current source with a precise measurement function
  • Power source and sink up to 110 V / 3.2 A / 60 W
  • Basic accuracy ±0.02%
AE Techron T3700
Transformers for electrical field sensitivity
  • High-voltage transformer: 1:37 step-up
  • Frequency range: 250 Hz to 35 kHz
  • Tested up to 5,000 VDC
AE Techron T2000
Conductive low-frequency sensitivity transformer
  • 2:1 step-down transformer
  • 10 Hz to 250 kHz, up to 200 W and up to 40 A AC/DC secondary current
  • Thermal protection on the primary side, 35 A fuse on the secondary side
AE Techron T1000
Magnetic Field Sensitivity Transformer
  • Magnetic field transformer
  • Up to 100 A RMS on the secondary side and up to 300 A·m field strength
  • Overcurrent protection (12 A fuse)
AE Techron 9100 Series
Switch-mode amplifiers with wide bandwidth and high power
  • Broadband power amplifier: DC to 250 kHz
  • Slew rate up to 150 V/μs, voltages up to 200 Vp and currents up to 540 A RMS
  • Four-quadrant operation
Yokogawa MY600
Digital multimeter with an interface for a PC or tablet
  • Insulation resistance measurement up to 4000 MΩ
  • Interface to a PC or tablet for data transfer
  • Automatic range selection
Yokogawa AQ23811A
It is ideal for testing semiconductor devices at low to medium currents and can be expanded to up to 18 channels using a 9-slot frame.
  • Source Measure Unit
  • ±6 V / ±600 mA (source), DC and pulse operation (50 μs to 1 s)
  • Measurement resolution down to the pA range
APM SPST Series
High power density, 3-phase output
  • 3-phase AC power supply system
  • 15 Hz to 1,000 Hz
  • Built-in power meter
APM SPS-M/A Series
DC Power Supply Systems
  • Up to 2,250 V, 3,000 A and 180 kW per cabinet
  • Modular system design
  • Flexible operating modes & control
APM SPS-300
high power density, high reliability, high precision
  • Programmable AC power supply
  • 15 Hz to 1,000 Hz
  • Built-in power meter
APM SPS Series
DC Power Supply Systems
  • 12 kW to 40 kW per unit
  • Voltage ranges up to 1200 VDC and currents up to 2000 A
  • Supports CV and CC operation, LIST / STEP / SEQUENCE programming
APM SP-3U/6U
Enables high efficiency at every stage
  • 6 kW to 36 kW per unit
  • Voltage ranges up to over 2000 VDC
  • Can be connected in parallel with up to 16 units